How to setup a Core XY replicape
This is a first pass at documenting how to set up a Replicape board to run a CoreXY printer.
- I'm going to assume you have a basic amount of Clue and can find your way around at the command line for this pass.
- I can go back later and flesh it out with more detail.
I'm not going to cover how to install the software, as that's already explained over at the Thing-Printer Wiki
You should gather the following information:
- Stepper motor specs, specifically the maximum current they can handle
- Print bed dimensions
- Limit switch locations
- Homing directions (will be related to the limit switch locations above)
BeagleBone Black / Wireless (BBB)
- System board that the entire stack runs on.
- Runs Redeem ('firmware')
- Runs Toggle ('display controller')
- Runs OctoPrint ('print controller')
Theory of Operation
Once you have the software installed,updated, and running, you connect to the OctoPrint software that is running on the BBB and do the initial setup on it.
- Need to expand this later
As you step through the setup:
- Recommended that you keep Access Control Enabled for security reasons.
- Set your print bed dimensions
- Axis speeds can be left at the defaults, as they only control the manual movements that you make through OctoPrint.
Once OctoPrint is set up, log in if you're not already (upper right corner).
Click on the Settings wrench at the top, near the login button.
At the bottom of the page that comes up, click on the Redeem Plugin option.
There's several items on this page you need to be aware of and how they interact with each other.
Redeem uses several config files.
- Top level config file. The system looks here first.
- This file can be directly edited in the Redeem Plugin interface in OctoPrint.
- If it doesn't find what it needs, it falls through to...
- The system looks here if it doesn't find a needed config item in the local.cfg file
- Has model specific configuration info. Look through the list and find a file that is at least similar to your printer, then click the star on the right to set it as the preferred config.
- If you're setting up a CoreXY design, you'll want to select the maxcorexy.cfg profile
- This is the 'fallback' if the system doesn't find the needed information in any of the other config files.
- default.cfg has all options, and they are configured with sane defaults.
Any changes you need to make should be made in the local.cfg file. Any option you set in there, will override the other files. Keep your edits to the local,cfg file, as printer.cfg and default.cfg may be overwritten on software upgrades
One suggestion is to view the maxcorexy.cfg and copy/paste the entire cfg into the local.cfg, then make your edits there.
Values in this are in meters, or meters/sec
These are the offset of the limit switch from 0,0,0. If you are homing to X_Minimum, Y_Minimum, and Z_Minimum, these should all be 0.0. If you are homing to the Maximum on an axis (for example, Y_Maximum), then this will be the distance from Maximum to 0
- Axis in the config are named for the terminal they're connected to on the board. Typically, X, Y, and Z are connected to the appropriate axis, E is connected to the Extruder, and H is usually a second Extruder or a second stepper that is slaved to another axis
This section defines the print bed dimensions and the limit switch offsets
axis_config = 2 #This tells Redeem you're running a CoreXY machine (more info in default.cfg) travel_x = 0.250 #X dimension in meters (for this entry, the print bed is 250mm wide) travel_y = 0.150 #Y dimension in meters ( 150mm wide ) travel_z = 0.300 #Z dimension in meters ( 300mm vertical ) offset_x = 0.000 #X homes to X_Minimum, so there is no offset for it offset_y = 0.150 #In this example, Y homes to Y_Maximum, so there is an offset to tell Redeem where 0 is for the Y Axis. offset_z = 0.0 #Z homes to Z_Minimum, so no offset for it
This section defines your stepper motors. Setting 7 is the 'quarter step stealthchop' and is very quiet. Anything lower tends to be noisier.
microstepping_x = 7 microstepping_y = 7 microstepping_z = 7 microstepping_e = 7 microstepping_h = 7
Current in amps to run each stepper at. Anything above 0.5 will require a cooling fan on the Redeem board. Do not go above the max rating for your stepper (from the Prerequisite section above) or 1.2A (whichever is lower). Starting at about 0.4 is a good starting point. If the motors are running hot after a print, you should lower the current. If you are skipping steps, raise the current. It is STRONGLY recommended that you install heat sinks on the TMC2100 driver chips.
current_x = 0.4 current_y = 0.4 current_z = 0.4 current_e = 0.4 current_h = 0.4
Steps per millimeter for the stepper. No microstepping is used here, that is defined above in the microstepping_* option
steps_pr_mm_x = 5.0 steps_pr_mm_y = 5.0 steps_pr_mm_z = 25 steps_pr_mm_e = 10 steps_pr_mm_h = 25
If your steppers are whining/singing, set this to 0. Need to expand on this a bit more
slow_decay_x = 0 slow_decay_y = 0 slow_decay_z = 0 slow_decay_e = 0 slow_decay_h = 0
Direction for the steppers to turn. If you need to reverse a stepper, just set it to -1. Your steppers should be plugged in the same way (black wire to Pin 1 or Pin 4) and just control your direction here. If the majority of your settings here are -1, power down and flip the connectors 180 degrees
direction_x = 1 direction_y = 1 direction_z = 1 direction_e = -1 direction_h = 1
A stepper controller can operate in slave mode, meaning that it will mirror the position of the specified stepper. Typically, H will mirror Y or Z, in the case of the former, write this: slave_y = H.
in_use_h = True # Enable the slave stepper driver slave_z = H
temp_chart_e = HT100K3950 # List of temperature charts can be found at here temp_chart_hbp = HT100K3950 max_temp_E = 280.0 #Extruder maximum temp. 250.0 is a safe number if you are only printing PLA. ABS and PETG will need a higher limit set here (such as 280.0)
invert_x1 = True # True means endstop is connected as Normally Open (NO) or not connected invert_y2 = True # False means endstop is connected as Normally Closed (NC) invert_z1 = True # You can check these with M119 in the OctoPrint terminal invert_x2 = True invert_y1 = True invert_z2 = True
# If one endstop is hit, which steppers and directions are masked. In other words, what directions should the stepper NOT be allowed to turn # The list is comma separated and has format # x_cw = stepper x clockwise (independent of direction_x) # x_ccw = stepper x counter clockwise (independent of direction_x) # This *is* affected by the direction_* option above. # # Steppers e and h (and a, b, c for reach) can also be masked. # # For a list of steppers to stop, use this format: x_cw, y_ccw # For CoreXY and similar, two steppers should be stopped if an end stop is hit. # similarly for a delta probe should stop x, y and z.
end_stop_x1_stops = x_cw,y_cw #This stops the X and Y motors from turning clockwise when the X1 stop is hit (X_Minimum in this example) end_stop_y2_stops = x_ccw,y_cw #This stops the X motor from turning CCW and the Y motor from turning CW #(Y_Maximum is the location of the limit switch) end_stop_z1_stops = z_cw,h_cw #This stops the Z and H motors from turning CW when the Z_Minimum limit switch is hit #(H is mirrored to Z, so we have to include it here Otherwise, Z would stop turning, but H #would continue to turn
# Max speed for the steppers in meters/sec max_speed_x = 0.3 #This sets the maximum speed to 300mm/sec for X max_speed_y = 0.3 #300mm/sec for Y max_speed_z = 0.3 #300mm/sec for Z max_speed_e = 0.2 #200mm/sec for the extruder max_speed_h = 0.3 #300mm/sec for H, which is slaved to Z (above) #Maximum acceleration in meters/sec acceleration_x = 1.5 #1500mm/sec acceleration acceleration_y = 1.5 acceleration_z = 0.5 #500mm/sec acceleration acceleration_e = 1.5 acceleration_h = 0.5
#Homing speed in meters/sec home_speed_x = 0.05 #Homing for X is be 50mm/sec. It is set to a positive value, as it is homing to X_Minimum home_speed_y = -0.05 #Homing for Y is 50mm/sec. It is set to a negative value, as it needs to home to Y_Maximum home_speed_z = 0.01 #Home for Z is 10mm/sec home_speed_e = 0.01 home_speed_h = 0.01
connect-therm-E-fan-1 = True #Connects the thermistor on the extruder to control the fan plugged into Fan1. In this instance, that is the hot-end cooling fan (not the part fan) therm-e-fan-1-target_temp = 50 #Default temperature is 60C. This will change that to 50C. add-fan-0-to-m106=true #I have the part cooling fan plugged into Fan0. This line tells Redeem to use Fan0 when the GCode tells it to turn on the part fan
#0 is off, 1 is on default-fan-0-value = 0.0 default-fan-1-value = 0.0 default-fan-2-value = 0.0 default-fan-3-value = 1.0 #I have a fan plugged into Fan3 to cool the Replicape itself. This line turns the fan on.